Guy Spends $500 To Build An Epic Custom Guitar Out Of 1200 Pencils, Shows How He Did It

People make a lot of cool material from colored pencils. And when Burls Art realized them, he decided to take it up an octave.

“I assured a lot of people online inducing bowls out of colored pencils and I thought that was really cool but I wanted to make something that I can actually utilize and enjoy more so than a bowl when it’s finished, ” Burls Art told Bored Panda . “Since I play guitar, I believed this would be a cool programme that would accomplish that objective. I decided on making a( Fender) Stratocaster styled electric guitar … This was the first guitar I’ve ever built”

“It was surprisingly not as difficult as I would have imagined, ” he said. “The only real struggles didn’t come as much with the actual guitar constructing as much as it did with the colored pencil material. By that I intend, the color of the colored pencil would smear when sanded with high grit sandpaper and it appeared dreadful. So I had to figure out a route to achieve good timber/ lead color without smear( which I detail in the video at the end of this post ). ”

“That’s 1200 colored pencils. Bought the cheapest ones I could find on Amazon. They objective up being nearly identical to Crayola.”

“Cheap harbor freight mini miter assured cutting the pencils into 2 ” pieces”

“Cutting the pencils was far and away the most tedious segment of the build”

“In goes the epoxy resin”

“This is a milling jig that I made out of some spare lumber I had. The router slides back and forth on here and the jig slips left to right so that I can take off about 1/8 ” off of the pencil slab. This essentially planes the slab for me”

“Tracing the template onto the slab”

“The epoxy resin/ pencils combination was far too dense for me to cut with a jig imagine alone, even employing a diamond blade. Because of this, I had to drill out the pencil cores to stimulate life a little bit easier on the jig saw”

“Super gluing the template on. I taped a few strips of masking videotape onto the guitar and a few strips onto the template … Little bit of superglue on the masking tape and connect them together. Makes for an incredibly strong lateral hold that can easily be drawn off with no damage done to either the guitar or template”

“Routing the side of the body utilizing a table router. This was another homemade jig using the wooden workbench and a 3×3 piece of melamine lumber. Cut a hole in the middle of the melamine board and mount the router on the bottom side. Run well. This 2.5 ” router bit is a bit frightening though, I cannot lie”

“Routing the leading edge gives me a near perfectly shaped body”

“Routing the cavities and neck pocket”

“This is an example of one of my fights with the develop. The entire block was sanded with 80 grit on the belt sander. Then the left side was progressively sanded up to 360 grit. So the highest grit I moved, the more colouring smear would occur. Smearing was minimal until I went above about 220 grit. This left me with 2 selections .. either have a smooth surface and a grayish/ smeared colour tone … or … have good clean timber and resulted colours but at the costs of merely enabled to sand to 220. The option was pretty obvious to me lies in the fact that the colored pencils were the star of the develop … I wanted to showcase their colours as much as possible”

“Fixing some tear-out I had when routing the neck pocket”

“Lots of sanding”

“Drilling the neck mounting holes. I likewise drilled the bridge mounts at this time. This is like a portable drill press btw … Not as good as the real thing, but it gets the job done”

“Throwing on some clear coat! I applied a 2-part spraying enamel, which is really nasty material … but it commits a beautiful finish. Dumped the entire can on it in 5 coats”

“The polishing compound I used”

“Easily the most fulfill part of the build”

“Mounting the tremolo”

Finished !!!!

“The more difficult portions of the construct only had to do with figuring out ways to make use of the limited equipment and power tools that I had. For instance, making a makeshift milling machine( ie: planer ), making a router table out of my wooden workbench, etc .. But it goes to show that you can make a guitar in your garage with limited tools if you get a little creative.”

Burls Art couldn’t put an accurate number on the time it took him to complete his project. “I worked on it for 4-5 weeks for a few hours a day, like 2-4 hours probably. It took a long time, but for the most part, it was enjoyable. I think I could make one faster now though since I know the processes and things that I would do differently. I’d say I spent in the neighborhood of $500 on it, but some of that includes router bits and other parts of equipment that I didn’t already have. I already had the guitar neck and hardware though so that saved some money.”

He was really happy with the final looking of the guitar. “It’s a one-of-a-kind guitar as of now which I guess is pretty cool, though that’s likely soon to change now that the idea’s out of the bag.” He promised, nonetheless, that the matter is won’t be his last unique guitar develop. “I have a lot more minds that I reckon will translate well that I’m going to take on in the future. Some that I belief will even be more interesting than this colored pencil guitar.”

Read more: http :// www.boredpanda.com/ 1200 -colored-pencils-electric-guitar-flyjumper /~ ATAGEND

Author: Moderator

Leave a Reply

Your email address will not be published.